Are you still stuck in the tedious cycle of cleaning after your cleaner?

Picture this: every time you want to mop your floors, you first have to fill the heavy water tank, carefully measure out cleaning solution, and once the job is done—spend twenty minutes crouching over the sink, hand-scrubbing dirty, greasy mop pads.

It’s time-consuming, physically exhausting, and completely defeats the purpose of buying a "smart" home device.

At uninell, we believe true automation should mean total freedom. That’s why we created the uninell Z10—a next-generation robot vacuum and mop engineered to eliminate every single friction point of traditional floor care. Here is how the Z10 takes total control of your cleaning routine so you can spend your energy on what actually matters.

1. Zero-Touch Mop Care: 122°F Hot-Water Washing & Dual-Temp Drying

Washing dirty mop pads by hand is easily the worst part of floor cleaning. Cold water fails to dissolve stubborn kitchen grease, leaving your hands covered in grime and spread-out oils.

The uninell Z10 automates the entire process with 122°F Hot-Water Self-Cleaning Mops:

• Automated Deep Cleaning: At 122°F, high-temperature water melts away hardened grease and stubborn dirt instantly, restoring mop fibers to peak freshness—without you ever touching a dirty pad.

• Hands-Free Rinsing: The base station automatically power-washes and rinses the mops before, during, and after each cleaning session.

Dual-Temperature Hot-Air Drying (104°F vs. 140°F) Damp mops left to air-dry create foul odors and breed bacteria. The Z10’s automated hot-air system dries your mops hands-free using two tailored temperature modes:

• 104°F Gentle Eco Dry: Quiet, energy-efficient daily drying that keeps mop fibers plush and intact.

• 140°F High-Heat Rapid Dry: Powerful sanitizing heat that blasts away moisture, preventing mold and bacterial growth even during humid rainy seasons.

2. Self-Cleaning Base Station with Dual Scraping Arms: Zero Station Maintenance

Traditional robot stations hide a dark secret: while they wash the mop, dirty water, hair, and sludge collect at the bottom of the base itself. Cleaning these cramped, fixed dock corners usually requires scrubbing on your hands and knees with towels and toothbrushes.

The uninell Z10 solves this ultimate industry pain point with a Dual-Protection Station Maintenance System:

• Dual Scraping Arms Auto-Clearing: As the mop washes, high-precision dual scraping arms automatically clear dirt and debris from the base surface, driving wastewater and sludge directly into the suction outlet so gunk never settles or builds up.

• Detachable Base Tray for Effortless Upkeep: For long-term deep care, the Z10 features a modular, detachable bottom tray. Simply pop it out with one click, rinse it under running water in 5 seconds, and snap it back in.

No awkward crouching, no trapped sludge, and zero dirty hands required.

3. Fully Automated Refill & Dosing: No Messy Hands, No Guesswork

Interacting with water tanks and detergent bottles mid-clean ruins the hands-free experience. The Z10 replaces manual labor with full-cycle automation:

• Auto-Water Replenishment: The base station continuously tops off the robot’s internal reservoir, ensuring consistent moisture from start to finish without manual refilling.

• Auto-Dosing Cleaning Solution: Say goodbye to sticky hands and spilt detergent. The Z10 automatically dispenses the perfect ratio of cleaning solution directly into the water stream for pristine, streak-free floors.

Reclaim Your Free Time with the uninell Z10

Upgrading to the uninell Z10 isn't just about getting cleaner floors—it's about reclaiming your time, protecting your hands from dirty water, and enjoying a living space that stays effortlessly pristine every day.

Stop hand-washing mops and refilling tanks manually. Step into the future of truly autonomous home cleaning.

👉 [Discover the uninell Z10 Today & Claim Exclusive Launch Offers]